Determination of optimal samples for robot calibration based on error similarity

Industrial robots are used for automatic drilling and riveting.The absolute position accuracy of an industrial robot is one of the key performance indexes in aircraft assembly,and can be improved through error compensation to meet aircraft assembly requirements.The achievable accuracy and the difficulty of accuracy compensation implementation are closely related to the choice of sampling points.Therefore,based on the error similarity error compensation method,a method for choosing sampling points on a uniform grid is proposed.A simulation is conducted to analyze the influence of the sample point locations on error compensation.In addition,the grid steps of the sampling points are optimized using a statistical analysis method.The method is used to generate grids and optimize the grid steps of a Kuka KR-210 robot.The experimental results show that the method for planning sampling data can be used to effectively optimize the sampling grid.After error compensation,the position accuracy of the robot meets the position accuracy requirements.     

电子信息系统复杂电磁环境效应研究初探

电子信息系统复杂电磁环境效应是指复杂电磁环境对电子信息系统的影响,是一个涉及社会和国防多个应用领域的重要问题.从电子信息系统复杂电磁环境效应概念出发,首先与电磁环境效应概念进行了比较分析,继而将研究分解为复杂电磁环境特性与模拟、复杂电磁环境综合效应机理和电子信息系统效能评估理论三个方面,最后给出了这三个方面的具体研究思路,并探讨了开展研究的一般性方法.     

Transient simulation of regression rate on thrust regulation process in hybrid rocket motor

The main goal of this paper is to study the characteristics of regression rate of solid grain during thrust regulation process. For this purpose, an unsteady numerical model of regression rate is established. Gas–solid coupling is considered between the solid grain surface and combustion gas.Dynamic mesh is used to simulate the regression process of the solid fuel surface. Based on this model, numerical simulations on a H2O2/HTPB(hydroxyl-terminated polybutadiene) hybrid motor have been performed in the flow control process. The simulation results show that under the step change of the oxidizer mass flow rate condition, the regression rate cannot reach a stable value instantly because the flow field requires a short time period to adjust. The regression rate increases with the linear gain of oxidizer mass flow rate, and has a higher slope than the relative inlet function of oxidizer flow rate. A shorter regulation time can cause a higher regression rate during regulation process. The results also show that transient calculation can better simulate the instantaneous regression rate in the operation process.     

液压减震器动力特性的影响因素研究

介绍了摩托车液压减震器的结构及原理，建立了其动力特性的理论模型。通过数字仿真计算研究了液压油的容性、感性等对减震器动力特性的影响情况，得出了两者影响刚好相反的结论，并与实际测量结果对比，验证了模型的正确性。这对减震器性能优化及结构改进具有指导价值，为建立基于几何尺寸参数的减震器动力特性模型奠定了基础。     

纳米技术

概述本世纪尚未开发的高新技术一纳米技术的兴起和研究进展。     

磁轴承控制器的设计及仿真研究

介绍了磁轴承系统的组成，对控制器性能的基本要求及控制方案的选择，分析了典型ＰＩＤ控制器存在的两个弊端，提出了磁轴承控制器的四种模型。通过对这四种模型的仿真研究，分析了各模型中比例系数、积分时间常数、微分时间常数及局部反馈系数对系统性能的影响，并给出了各参数较为理想的参考值及阶跃响应曲线，仿真结果对制作模拟控制器及数字控制器有一定的借鉴作用。     

3-D position estimation of isolated target and optimal trajectory choice in parasitic synthetic aperture radar

Bistatic SAR (BSAR) systems have recently been the subject of several studies, but little attention has been given to the potential of the location of targets. In the paper, the performance of the estimation of 3-D position of a target (TPE) in parasitic SAR is obtained analytically and illustrated by computer simulation using ambiguity function analysis, and the maximum likelihood estimate (MLE) approach. It was shown that by using a multi look parasitic BSAR all three coordinates of an isolated point target (IPT) could be evaluated. Analytical closed form equations that characterize the measurement accuracy were derived. In the final these equations will be used to demonstrate various cases of more practical, including optimal trajectories choice under any geometry configuration case, moreover, the conclusion is verified via Matlab.     

一种摇臂式起落架的两种建模及结果对比

为了满足适坠性能要求,一种摇臂式起落架采用了双腔缓冲器。本文详细推导了拉格朗日方程下该起落架的动力学方程,并编程数值计算了四种状态的着陆性能。同时在Adams/Aircraft平台下建立了该起落架模型,通过编写子程序的方法实现了该双腔缓冲器的功能扩展。Adams/Aircraft平台下的仿真结果与数值计算的结果吻合较好,为起落架性能分析提供了很好的相互验证方法。     

亚声速进气道设计敏感参数仿真分析

对不同气动布局的两种亚声速进气道建模,并针对两种进气道的敏感参数进行分析。通过对背部双发布局飞机进气道的隔道高度和喉道设计马赫数参数的研究可知,隔道高度增大或者喉道设计马赫数减小,使得进气道出口总压恢复系数增大,增量约0.5%。而对背部单发复杂形状进口(M型进口)布局飞机进气道的喉道形状研究显示,喉道形状越接近进口形状,进气道性能越好,较其他喉道形状进气道,M型喉道进气道出口总压恢复系数最高,最大增量约为1.5%。